As CES 2016 wrapped up this week in Las Vegas, Rogers was found to be featured in CES Daily magazine, January 9, 2016 – Day Four Edition, on page 50 of the audio section.
The new 34S-1 Integrated Amplifier was discussed. Some general information and features were highlighted and can be seen below.


Rogers High Fidelity Unveils the 34S-1 High-Performance Class A Integrated Amplifier with Eight EL-34 Power Tubes

January 6, 2016 / Warwick, NY: Rogers High Fidelity debuts its’ anxiously anticipated, class A, high-performance Eight-tube Class A Integrated Amplifier, the 34S-1 at the 2016 Consumer Electronics Show, Las Vegas.

Roger's High Fidelity new 34S-1 Amplifier photographed on Thursday, December 17, 2015.  © Chet Gordon • Photographer

Roger’s High Fidelity new 34S-1 Amplifier © Chet Gordon • Photographer

Powered by eight EL-34 analog vacuum tubes, the 34S-1 integrated amplifier delivers monster performance and a dazzling listening experience. Consistent with Rogers High Fidelity’s gold-standard requirements, this Class A integrated Amplifier boasts superior precision, aerospace engineering and hand-made craftsmanship that presents a new level of realism in audio reproduction.

 © Chet Gordon • Photographer

© Chet Gordon • Photographer

The Model 34S-1 flexes these dynamic features:

• Eight EL-34 tubes–four, for each channel and eight total for stereo operation following a true dual mono design
• Class A operation, military specification components, point to point Teflon wiring all carefully manufactured to the highest specifications
• Control capability via Bluetooth connection to both Apple and Android smartphone applications the 34S-1 displays on application control functions of all the amplifiers features: Ultra-linear and triode modes, Volume, Input and the Status of the power tubes in real time operation using visual indicators.
• Dual power supply circuit can easily handle large dynamic transitions in the audio signal being delivered while maintaining a smooth and clear midrange; vocals are presented with a truly rich and warm feel.
• Auto bias circuit for long tube life and ease of operation.
• One piece billet aluminum front panel, aviation grade quality chassis all made in the USA in Warwick New York
• Lifetime transferable warranty.

DSC_4667 small

The 34S-1 provides state of the art noise and distortion performance using all Teflon wiring and mil spec components. Another bonus feature is the isolation of each audio channel using a dual power supply design and a dual mono circuit point to point design. Even the most critical of listeners of the 34S-1 will enjoy the finest, organic tube sound quality with stunning three-dimensionality, low-level detail-retrieval and holographic sound staging.

In addition to releasing the 34S-1integrated amplifier at the Las Vegas Consumer Electronics Show, Rogers High Fidelity is demonstrating its current top-of-the-line Integrated Amplifier, the EHF-200 MK2—featuring the latest power tube on the market, the KT150. This new tube emphasizes power, headroom and perfect tonal qualities.

DSC_4635 DSC_4648 DSC_4683 DSC_4651

Rogers High Fidelity continues to bring to market the latest technologies, the best sound and an all-aerospace design. Come see and hear the newest addition to our Rogers High Fidelity product line by visiting the Rogers’ team at CES 2016, Venetian Hotel Suite # 29-124.

Located in the heart of the Hudson Valley in Warwick, NY, Rogers High Fidelity specializes in designing and manufacturing high-performance audio products. All Rogers High Fidelity products are completely made in the USA with the finest components, and feature a lifetime transferable warranty.

1 2 3

President and Chief designer Roger Gibboni applies his 30 years in aerospace communications design to create visionary solutions for true audio reproduction.


Also, the ultimate control application easily integrates Apple® iOS® and Android™ devices with the Rogers High Fidelity Control System to monitor tube status and control all amplifier functions.

34S-1 MSRP- TBD / Available March 2016


The International Consumer Electronics Show (CES) is a global consumer electronics and consumer technology trade show that takes place every January in Las Vegas, Nevada.


Please visit our display in Las Vegas at the International CES, show room 29-124 at the Venetian Hotel. Our founder and lead designer, Roger Gibboni, will join several other industry experts to present the finest audio products available.


– NEW Product Debut –


Rogers will be debuting their NEW Flagship Integrated Amplifier, the 34S-1!

34S-1 – a new unique Class A amplifier using:
• EL-34 Tubes in Dual quad per-channel design
• Plus a unique Bluetooth Control Interface

14 Dec 2015

Join Us In NYC on January 29th!

There are no tags 0 comments


Our Founder and CEO, Roger Gibboni, will be at Stereo Exchange at 627 Broadway in New York City from 7:00 to 10:00 PM on January 29th 2016 for Cosmos Sunshine’s Record Release Party. Please stop by for this unique event!

Friday, January 29th 2016 | 7:00 PM – 10:00 PM | @ Stereo Exchange – 627 Broadway NY


Event Line-Up

7:00 PM:
Event Start

8:00 PM: Album presentation on statement analog system (Totem, Rogers, Clearaudio, Transparent, Ortofon) in Bay 3. Cosmos Sunshine album listening session, ‘The Butterfly Fight Club’  – track by track, and discussion of the production, songwriting etc.

9:00 PM: Live performance by Cosmos Sunshine in Bay 1.

10:00 PM: Event Wrap-Up

16 Oct 2015

Rocky Mountain Audio Fest Press Award

There are no tags 0 comments

rmafThe Rocky Mountain Audio Fest is one of the only events in North America truly dedicated to high-end audio making it one of our favorites of the year. This year was especially wonderful as we created a “Made In America” system with VPI Industries, EgglestonWorks, Transparent Audio and Ortofon. Here is a listing of the equipment:

  • Rogers High Fidelity PA-1A Phono Stage and EHF-200 MK2 Integrated Amplifier
  • VPI Avenger with 1 JMW 3D-12 Reference arm (in a matching Roger’s red finish!)
  • Egglestonworks “The Camilla” loudspeaker
  • Transparent Audio Cable’s Generation 5 Ultra cable
  • Ortofon Cadenza Bronze

rmaf rogerThe highlight of the weekend for us was being awarded the Rocky Mountain Audio Fest Press Award for our PA-1A Phono Stage. This award was selected and voted upon by an “anonymous ballot of the world’s leading HiFi press publications.” To receive acclaim like this from such an esteemed group of individuals with incredible competition is something we are extremely proud of.


07 Oct 2015

Join Us In NYC on October 15th!

There are no tags 0 comments

Our Founder and CEO, Roger Gibboni, will be at Stereo Exchange at 627 Broadway in New York City from 12:00 to 730pm on October 15th. Please stop by for this unique event!

oct15-2 655






Rogers High Fidelity is thrilled to announce its inclusion in the 2015 list of Stereophile recommended components!


Our PA-1A Phono Preamplifier has solidified its position as a CLASS A component back-to-back years! Class A means it is recommended unequivocally regardless of price:

Roger GIbboni’s first phono preamplifier uses three tubes per channel for MM cartridges, and adds to its MC inputs a pair of internal step-up transformers. (Even more gain can be had, albeit at a slight cost in noise, by substituting for the PA-1A’s 12AU7 tubes a spare pair of 12AX7 tubes, also supplied). Capacitive and resistive loading are user adjustable, and a mute switch is included. Build quality is, as MF wrote, “impressive by and standard,” and tube life is expected to be in the neighborhood of 10,000 hours. MF praised the PA-1A’s “glorious, mesmerizingly rich midrange, and the overall drive and musical flow for which tubed phono preampls are renowned,” while nothing “the les-than-taut-and-punchy bottom end for which they are known.” MF also discovered in the Rogers phono pre some susceptibility to hum with both MM and MC cartridges, necessitating care with cable choice and physical placement. His verdict: “If you listen mostly to acoustic jazz and/or classical music, the Rogers PA-1A, paired with a cartridge that’s fast, open and extended on top, could be your ticket to long-term satisfaction.”


PA-1A Lifestyle-5

The EHF-100 MK2 enjoys its continued spot on the recommended component list for the 3rd year:

Made in the US by former NASA engineer Roger Gibboni, the EHF-100 is rated to deliver 65Wpc (JA measured 35Wpc) into 8 ohms; offers four pairs of line-level inputs; and uses two EF86 miniature pentode, two 12AX7 triode, and four KT88 power tubes. Fit and finish were excellent. Though not as nuanced, colorful, or dramatic as AD’s reference Shindo seperates, the EHF 100 distinguished itself as a tight, punchy-sounding amplifier with loads of natural detail, a very good sense of momenutm, and an excellent sense of space. Despite differences in the noise floor between its two channels, the EHF-100 measured well “for a classic design,” said JA.



Rogers High Fidelity is pleased to announce our new

Read more about it here
A purchaser of any new Rogers High Fidelity amplifier will be entitled to a free trip to beautiful upstate New York to see how your amplifier was created. We will be covering the customers expenses for lodging at a local Bed & Breakfast, transportation to/from local airport and lunch at the factory.


As more manufacturing moves overseas, Rogers is proud to handcraft all of our amplifiers right here in the United States. We want our customers to share in this pride and are excited to offer this industry first program.


DSC_6825Rogers_logo_75_pxantpic 008

HifiSenses just wrote a wonderful article highlighting the Rogers High Fidelity EHF-200MK2 Integrated Amplifier.

Read it below or click here!

The midrange was where the wonders are. The tube’s capability of endowing realistic dimensionality was desirably demonstrated. Kasia Lins “Cover Me” was delivered with breathtaking vivaciousness that emotionally zoned me out for a moment. The voices were sweet and creamy, harmoniously blended with the details that were extended in the treble.



In my audiophile journey, there was a period of time when I ventured into integrated amplifications. Considering it the most cost effective and space saving audio products that meet my budget and requirements at that point of time. The initial version of integrated amplifiers combined the pre & pro amplification in one body. But It gradually grew into multi features / functions integrated device with built in DAC, phonostages, WIFI, Bluetooth and many more.

Many consumers were then confused between an integrated amplifier with an Audio Video Receiver (AVR) as both are amplifier in principal function to drive loudspeakers. In terms of functions and features, the AVRs possessed abundance of them with other stuff like room correction, multi channel audio coding, video upscaler etc., with ability to perform not just stereo but home theatre multi channel amplification. All these made it pretty clear that the AVRs are more value for money comparatively for a new comer. However, despite that AVR is exceling in terms of multi features capability, their core amplification function is easily outshine by an audiophile grade integrated amplifier. That is why choosing a good integrated amplifier is so important in your line of audiophile journey and one should not be compromised with anything inferior, especially not audiophile grade.

Before we move on to the subject of today’s review, I would like to thank Bobby from Audioline whom generously loan the equipment to hifisenses and made this review possible. He is a wonderful guy and came down personally with his assistant to setup the review items in my place. Kudos to his commitment and extended personal touch.

Design and Build

The Rogers Fidelity EHF200mk2 integrated amplifier is a tube amplifier supplied with quad matched KT150 output tubes plus 2 x EF86 and 2 x 12AX7 input tubes. Its Input connection come in 4, all in unbalance and has an output connection for the subwoofer. This integrated amplifier also allows you to bypass its internal preamplification stage and use it solely as a dedicated amplifier. On its front panel, you have a headphone input jack, which make this a dedicated headphone amplifier as well. A good feature for those who need personal aural gratification at late night without disturbing others.

The Rogers Fidelity EHF200mk2 can operate in either triode or ultralinear mode, depending on individual’s preference. The unit runs pretty hot and definitely need ample headroom for ventilation. The Rogers trademark meter turns blue when powered up and it gave a grandeur feel together with its striking red chassis. The whole unit weighs a total of 28kgs mainly due to its large transformer housed on the rear of the device. Carrying them need some attention as the weight is lopsided on its rear, thus correct emphasize on handling is required.



Despite its striking red that shouts for immediate attention, beneath the chassis hides tour de force engineering that command equal appreciation. The whole amplifier works in Class A amplification plus auto bias capability. That means that the heat accumulated within is alarming high and will affect the components adversely. With regards to that, Rogers uses 18AWG military standard Teflon coating silver plated copper wire for all the internal wiring. The Teflon will not be damaged under prolong heated environment, proven in military test and that means better longevity of the components. Being a very particular person over heat impact on equipment MTBF, this added effort earns my utmost respect.

All the components used are of top grade and handwired directly for better reliability and serviceability. This enable Rogers Fidelity to honour a lifetime limited transferable warrant of their products. An icing that make your investment more worthwhile, not worrying the high depreciation of audiophile products. One of another thumbs up deal that Rogers contribute to this integrated amplifier is the power cable. Unlike conventional black power cord that many manufacturers throw in as a bundle, Rogers had supplied consumer with their proprietary Quiet Cable that comes with Furutech connectors and military standard Teflon silver-plated copper wire. Such attention to details makes me respect their commitment in providing the best without cutting corners.


The Rogers Fidelity EHF200mk2 was connected to both analogue and digital source with different genres of music playback. The listening review was conducted on both speakers and headphone demonstration, with type of music ranges from symphonic works, pop and jazz pieces.

Tube amplification has never failed to make it distinctively different from the solid state implementation. The Rogers EHF200mk2 presented a very clear top down tube sensation that I would relate to my first integrated amplifier, Octave V80. The KT150 gave me a very different sonic interpretation that I used to perceive. It was not as muffled and organic as I felt before, which surprises me in a good way as I recalled how I ditch KT150 for the KT120.



The treble delivery was definitely not edgy and surprisingly not muffled. Revelations in details was easily captured and that gave the symphonic works from Hans Zimmer’s “Time” from the soundtrack of “Inception” a pleasant to listen without cranking the volume. Subtle entrée following complex execution of the piece were all present without being uncompromised.

The midrange was where the wonders are. The tube’s capability of endowing realistic dimensionality was desirably demonstrated. Kasia Lins “Cover Me” was delivered with breathtaking vivaciousness that emotionally zoned me out for a moment. The voices were sweet and creamy, harmoniously blended with the details that were extended in the treble. This exceptional performance made listening of vocal pieces an edge compared with orchestral works.

Bass works are on a leaner side, not fat boomy like most tube amplifiers. Listening to the symphony bass performance generate coherency in overall tonal harmonization. However, listening to pop songs like Akon’s “Beautiful”, the essence of tight fast bass was amiss. This is especially obvious if you are a bass fan and been accumulating 80% of your listening time on such music genre. I would not say that this is a limiting factor for this amplifier; it’s actually a common signature for all tube amplifications in my opinion.

Soundstage was great but I felt that KT120 output tubes would do a better job in my opinion. I didn’t have a quad set to try thus readers can take it with a pinch of salt. Imaging was not razor sharp, that again I felt it’s the characteristic of KT150 that exudes more warmth in overall holographic sensation. It would be better with different output tubes in my opinion.

On the settings of Triode and Ultralinear mode, I prefer Triode mode for vocal presentation and Ultralinear for symphonic / pop pieces. Not all music can benefit from these modes, and it really depends on one’s preference in sonic presentation. However, this is a good add on feature, giving listener different options to try with.

Moving on to the headphone amplification side of review, a closed can Ultrasone Signature Pro and open can MrSpeakers Ether were use. Both cans received excellent performances, details and clarity was a notch higher than using loudspeakers. Especially on Ultrasone Signature Pro, the detail retrieval was distinctive and brought out more refinement in the songs. Soundstage was better on Ether then Signature Pro though but both performed equally well for the midrange delivery. One big difference I felt on the headphone and loudspeakers’ presentation is the holographic, three dimensional sensation. I can’t feel them in headphone implementation at all. Loudspeakers are still the best in provisioning a life like, at the venue impression comparatively.



Summary / Conclusion

Rogers EHF200mk2 tube integrated amplifier is one beast that I would not hesitate to recommend to readers. Aside from the excellent grade of material used and workmanship, the performance is top line and worth an audition if you are looking for your first or probably your last tube integrated amplifier.



  • Well engineered from inside out
  • Lifetime transferable limited warranty
  • Robust and all rounded amplifier that can drive almost any load


  • No balanced input
  • Chassis color finishes is either hate it or love it affair

The good people over at the absolute sound have written a great little article about our new factory location.

Read it below or click here!



The following is a press release issued by Rogers High Fidelity.

WARWICK, NY | July 23, 2015 – Rogers High Fidelity, a leader in home entertainment and Ultimate-quality audio, proudly announces the opening of a new factory location in Warwick NY.

Rogers High Fidelity audio products produces the highest quality handmade high performance class A stereo tube amplifiers,  with unsurpassed capabilities and styling together with a host of leading-edge features and functionality for audiophiles who demand the ultimate sound performance .

Rogers High Fidelity will be producing it fine line of audio products at its new location in Warwick NY.  A Grand Opening celebration will be held Tuesday August 11 from 6:00 – 8:00 PM at the factory’s location on 28 Church Street, Suite 3 Warwick NY.

About Rogers High Fidelity:
Since 2009, Rogers High Fidelity unwavering commitment to excellence, innovation and quality continues to define the state-of-the-art in high fidelity audio and provide discriminating consumers around the world an elevated home entertainment experience.

Rogers High Fidelity performance audio products are handcrafted at the company’s Warwick, New York headquarters.

Its products reflect unmatched levels of performance, superlative engineering and hand craftsmanship. Built to last for decades and carry a lifetime warranty.

All components meet military grade specifications and are sourced from USA suppliers and are handmade one at a time with advanced testing and quality control.

Rogers High Fidelity commitment to Sheer Elegance, Unmatched Efficiency and Reliability produce audio products that Boast New Engineering Advances in Tube Audio Technology Not Available in Other High End Audio Products, only from Rogers High Fidelity.

Awards and Achievements:
Rogers High Fidelity Model – PA-1A has been added to the 2015 list of Stereophile Magazine recommended components listing and has been awarded the 2014 Analog Product of the Year by Tone Audio Magazine.

1 2 3 4 5 6 7 8
Copyright 2015 Rogers High Fidelity.